FAAC Gate Motor Replacement Nationwide

FAAC Gate Motor Replacement: The Keller Owner’s Guide

We stock and install FAAC-compatible gate motor replacements throughout Keller, TX, with most swing and slide gate swaps completed in a single visit. Installed pricing typically lands between $850 and $1,600 depending on your FAAC series, arm style, and whether the control board needs replacing at the same time. The usual discovery is a gate that groans, stalls, or simply stops answering the remote, often on a Monday morning when you are already running late.

Call (254) 330-8718

FAAC builds solid hydraulic and electromechanical operators, but every motor has a service life. In Keller’s heat, capacitors and circuit boards tend to fail before the motor windings do. When a homeowner calls us about a dead FAAC, Victor Salinas usually starts with one question: “Tell me what it is doing and what it is not doing, that is usually all I need to get started.”

Key Takeaways

• We carry FAAC-compatible replacement motors and control boards on the truck for the most common residential series.
• Most FAAC motor replacements in Keller are done in one visit, with the price agreed before we touch a bolt.
• Every job is covered by our 90-Day Done Right Promise, in writing.
• Call (254) 330-8718 and a live person answers, any hour, any day.

Which FAAC Models This Applies To

Most residential FAAC operators we replace in Keller fall into three families: the 400 series swing gate operators, the 390/391 series for lighter swing gates, and the 740/741 series for slide gates. Your model number is printed on a silver or white label on the operator housing, usually near the release handle or on the inside of the cover. If that label has faded in the Texas sun, the arm style and the shape of the housing tell us most of what we need.

Here is the compatibility gotcha we see often: a FAAC motor is not a universal part. A motor from a 402 will not drop into a 400 without matching the hydraulic pump version, and the 741 slide operator uses a completely different drive assembly than the 400 swing line. Aftermarket equivalents exist and can save money, but we only install ones we have seen hold up in Keller’s summer heat. For older FAAC units where the OEM motor is discontinued, we will tell you plainly whether an aftermarket option makes sense or whether a full operator swap is the smarter money.

Ironworks Gate Co. is an independent service provider, not affiliated with FAAC. We stock FAAC-compatible parts and also keep motors and boards on hand for LiftMaster, Mighty Mule, and Ghost Controls, so if we find a mixed-brand setup at your property, one visit is usually enough.

Signs Your FAAC Gate Motor Replacement Is Failing

• Gate moves at half speed or hesitates before starting. This usually means the motor’s capacitor is degrading or the hydraulic fluid has thinned from heat cycling. You are feeling the motor work harder than it should, and failure usually follows within weeks.
• Humming sound but no movement. A motor that hums and does not turn is often a seized pump or a failed start capacitor. On FAAC hydraulic units, this sound is the pump trying to build pressure and failing.
• The gate opens but will not close, or closes but will not open, without tripping the breaker. This points to a failing limit switch or a board that has lost its programming, not always the motor itself. We test the motor separately before recommending replacement.
• Remote works intermittently, but manual release works fine. That tells us the motor and gate are mechanically sound, and the problem is in the operator’s electrical controls. On FAAC units, the most common culprit is the control board, which we replace independently when possible.
• You smell a faint electrical burning after the gate cycles. Do not run the gate again. That odor means windings are overheating or a capacitor is venting. Call us. A motor that is hot to the touch after a short cycle is a fire risk, not just an inconvenience.

Replacement Cost & What’s Included

A FAAC gate motor replacement in Keller typically runs $850 to $1,600 installed. The range is driven by three things: the motor series, whether you need the control board replaced at the same time, and whether we are doing a straight motor swap or replacing the full operator assembly. A basic 390-series motor replacement starts near the lower end. A 400-series hydraulic unit with a new board lands mid-range. A full operator swap on a slide gate with new limits and photo eyes sits at the top.

Every quote includes the motor, installation labor, wiring verification, limit setting, and a function test through a full open-and-close cycle. The price is quoted and agreed before any work starts, so there is no surprise on the invoice at the end. We also offer $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% discount for seniors and veterans.

DIY or Call Us?

Here is the honest split. You can safely check the power supply, confirm the breaker is on, and test the manual release to see if the gate swings freely. Those three checks take five minutes and tell us a lot over the phone. What you should not do is open the operator housing and start probing connections. FAAC operators carry live 120-volt wiring next to low-voltage control circuits, and a wrong move with a multimeter can fry the board you were trying to save or put you across line voltage.

We have also repaired enough homeowner attempts to say this plainly: a motor replaced incorrectly will burn out the new part or damage the gate leaf. The swap itself usually takes us under two hours when we do it. Call (254) 330-8718, describe what the gate is doing, and we will tell you over the phone whether it sounds like a motor, a board, or something simpler. The estimate is free.

FAQs

Call Ironworks Gate Co. for Your FAAC Motor Replacement in Keller

If your FAAC operator is groaning, stalling, or dead, call (254) 330-8718. A live person answers, 24 hours a day, 7 days a week. We will ask what the gate is doing and what it is not doing, give you an honest read over the phone, and schedule a visit that fits your day. The price is set before work begins, and every job carries our 90-Day Done Right Promise in writing. We have been serving Keller homeowners since 1984, and we plan to be here for another forty years. One call, one visit, done right.

Written by Victor Salinas, Owner & Gate Repair Technician, Ironworks Gate Co. at Ironworks Gate Co., serving Keller and nearby areas.