Ghost Controls Gate Installation Nationwide

Ghost Controls Gate Installation in Keller: What to Know First

Ghost Controls gate installation in Keller typically runs $450-$900 for a single swing gate opener installed on an existing gate, and $1,200-$2,600 when the job includes a new gate, post work, or dual openers on a double gate. Most Ghost Controls installs take us half a day to a full day, depending on what’s already in the ground. We quote a firm price before we start, and that price does not change mid-job.

Call (254) 330-8718

This page is for Keller homeowners who already own Ghost Controls equipment, or are considering it, and want a gate company that actually knows the brand. We’re an independent Ghost Controls service provider, not a manufacturer-authorized shop. That independence means we tell you the truth about what works and what doesn’t. If you’ve got a Ghost Controls opener sitting in the garage, or one bolted to a gate that’s never worked quite right, call us at (254) 330-8718 and tell us what it is doing and what it is not doing - that is usually all we need to get started.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls builds a solid opener for the money, and we install them regularly across Keller, Fort Worth, and the surrounding area. But every brand has its weak points. Here are the Ghost Controls issues we see most often on gate installation and service calls, and what we do about each one:

• Armature limit switch drift on the AXDP and GHP series. The linear actuator arms Ghost Controls uses in the AXDP and GHP lines have internal magnetic limit switches that can drift after a hard stop, like a gust of wind catching a wide gate. The gate closes fine for months, then one day it stops two inches short or over-travels and stalls. We reset and reposition the limits and verify the teach cycle so the arm stops exactly where it should, every time.
• Photo-eye alignment on installations near Keller’s sloping driveways. Many Keller homes sit on gentle grades, and a gate that shifts half an inch on its hinges changes the angle of the photo-eye beam. We see Ghost Controls systems that worked fine for a year suddenly refuse to close because the beam no longer lines up. Before replacing anything, we check gate sag, hinge wear, and post plumb, then shim or refit the photo-eyes to the actual angle of the gate, not the angle the manual assumes.
• Battery drain on the Ghost Controls solar-compatible boards. The GSP and AXDP boards accept solar input, which sounds great in Texas. In practice, we get calls from Keller homeowners whose opener works all summer then dies in early morning during late fall, when the angle of the sun shifts and the tree line near Bear Creek Park shades the panel. We test the battery under load and often find it’s borderline, not dead. Our fix is a load-tested replacement battery, a panel reposition, or a switch to a hardwired transformer feed if the driveway already has conduit nearby. We don’t throw parts at it until the diagnosis is clear.
• Remote range complaints on the older AXDP models. The earlier AXDP receivers had a small antenna routed inside the control box, which is fine on a test bench and marginal on a concrete-and-stone driveway entrance where the box sits behind a brick column. We relocate the antenna outside the enclosure or add a Ghost Controls-compatible antenna extension, and suddenly the opener works from the street instead of from five feet away. Simple fix that saves a lot of frustration.
• Warranty-safe motor swaps versus full unit replacement. When a Ghost Controls motor burns out on an otherwise healthy gate, we look at the arm and board first. Ghost Controls sells the motor as a replacement part, and on a gate that’s balanced and true, swapping the motor is a few hundred dollars cheaper than replacing the whole opener. We only recommend a full replacement when the board, arm, and power supply are all worn past the point where repair makes sense. Keller homeowners appreciate that we don’t push a new unit when a part will do the job.

Our Ghost Controls Gate Installation Process

Every Ghost Controls job follows the same path, whether it’s a new install on a fresh gate or a repair on a 12-year-old opener that’s been limping along. Here’s how it goes:

1. 1
   The call. You call (254) 330-8718 and tell us what’s on the driveway: single swing, double swing, sliding gate, pedestrian gate, the gate’s approximate width and weight, and what the opener is doing or not doing. Victor Salinas or one of our techs asks a few questions so we can bring the right parts the first trip.
2. 2
   Diagnosis on site. We check the gate itself first because a Ghost Controls opener cannot fix a dragged, sagging, or binding gate. Hinge wear, post lean, wheel-track alignment, and the true weight of the gate get checked before we turn a single bolt on the opener.
3. 3
   Parts decision. We lay out the options honestly: OEM Ghost Controls parts when the warranty or system age calls for them, quality aftermarket parts when the gate is out of warranty and you want to save money without sacrificing function. You get the choice, and we recommend based on what we’d install on our own driveway.
4. 4
   Installation. Mounting, wiring, limit setting, remote programming, and safety edge or photo-eye integration all happen in one visit for most jobs. We keep the work area clean and cover any wiring we run so it doesn’t look like an afterthought on your brick or stone.
5. 5
   Testing. We run the gate through thirty open-close cycles, triggering the auto-reverse and obstruction detection each time. We don’t hand you the remote until the gate operates the way it should from every angle the driveway gets used from.
6. 6
   The 90-Day Done Right Promise. We walk you through what we did, hand you the paperwork, and you’re covered by our written guarantee. If something isn’t right, we come back and make it right. No arguing, no forms to file.

What Ghost Controls Gate Installation Costs in Keller

We believe in straight answers, so here’s what Ghost Controls work runs in Keller in 2025 and 2026. These are firm ranges based on what we see week to week:

• Single swing gate opener install, existing gate: $450-$700, assuming the gate is balanced and posts are solid.
• Double swing gate install, dual openers: $950-$1,500, depending on opener model and whether the second arm runs off a shared board or two separate boards.
• Sliding gate opener install on an existing track: $800-$1,400, plus any track or roller replacement if the old hardware is worn.
• Pedestrian gate opener install: $500-$900, including the strike plate and lock integration if needed.
• New gate plus Ghost Controls opener: $2,400-$5,600, varying widely by gate material, size, and what kind of posts and foundation work the driveway needs.

What moves the price is the gate’s condition and weight, the power source available at the post, and whether we’re working with existing conduits or digging new ones. The estimate you get is the price you pay, and it’s quoted and agreed before any work starts. Call (254) 330-8718 and we’ll give you a free, written number.

Why Keller Homeowners Call Ironworks Gate Co. for Ghost Controls Work

We’ve been serving Keller and the surrounding communities for over 42 years, and in that time we’ve earned the kind of reputation that doesn’t need a billboard. Victor Salinas grew up in Keller and still lives a few miles from Bear Creek Park, so when we say we know the neighborhood, we mean it. When a gate motor quits the morning of a family gathering or a hinge finally gives out after a decade of hard use, neighbors call us first.

Our techs are trained on nine gate-automation brands, including Ghost Controls, LiftMaster, Mighty Mule, and DoorKing. That matters when you’ve got a Ghost Controls opener on the driveway and a LiftMaster on the back gate. One company, one call, both gates done in one visit. Every job is protected by our 90-Day Done Right Promise, and a live person answers the phone 24 hours a day. No voicemail trees, no call-back tickets, no waiting until Monday morning.

FAQs