Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Gate Installation in Keller: What to Know First
Elite gate installation in Keller typically runs $1,800 to $6,500 depending on gate size, material, and whether you’re adding automation. We’re an independent Elite service provider, and most installations are completed in a single day, with the price agreed in writing before we start. If you own an Elite gate and need it installed correctly the first time, call (254) 330-8718 for a free estimate.
This page is for Keller homeowners who’ve already purchased an Elite gate or are considering one, and want a straight answer about installation, cost, and what goes wrong. Over 42 years in this trade has taught us that the installation matters as much as the gate itself. A well-built Elite gate hung poorly will fail early. Hung right, it’ll outlast most of the fences it’s attached to.
How Elite Products Fail During Installation
Most Elite gate problems we see in Keller aren’t manufacturing defects. They’re installation errors that show up months or years later. Here’s what we regularly encounter:
- Elite SL3000 series sliding gates: misaligned track rollers. The SL3000 is a common sliding gate in Keller’s larger lots, and we see a pattern where the gate was installed with the track slightly out of level. It works fine for six months, then the rollers start wearing unevenly, and the gate develops a hitch in its travel. Our fix is a full track re-level and roller replacement, not just greasing the squeak.
- Elite swing gates with undersized hinges. A double swing gate needs hinges rated for the full leaf weight, wind load, and duty cycle. We’ve replaced hinges on Elite gates where the original installer used hinges that matched the gate’s look, but not its actual weight. In Keller’s spring wind season, those gates flex and sag. We size hinges to the leaf’s real weight, not the catalog photo.
- Elite actuator mounting plates pulling loose from brick columns. Many Keller homes have brick or stone columns. If the actuator plate is anchored with generic sleeve anchors into the mortar joint instead of epoxy-set anchors into solid brick, the plate works loose within a year or two. The gate then runs out of travel. We core and epoxy-set the anchors, a repair we do often enough that we carry the epoxy in the truck as standard stock.
- Elite Mighty Mule-equivalent control boards burning out from improper wire gauge. Elite’s entry-level automation boards are sensitive to voltage drop. We see installations where low-voltage wiring was run with 18-gauge thermostat wire over a 50-plus foot run. The board overheats trying to compensate and fails prematurely. We run 14-gauge or 12-gauge low-voltage wire on any run over 30 feet.
- Elite solar-powered gates installed in shaded Keller lots. This is a real one. A homeowner buys a solar kit assuming Texas sun is enough. But half the Keller lots we work have mature oaks and pecans shading the panel for much of the day. The battery chronically undercharges, and the gate dies at the worst moment. We walk the lot before recommending solar, and if the math doesn’t work, we say so plainly and recommend a hardwired power run instead.
Our Elite Gate Installation Process
Every Elite job follows the same unhurried sequence. No shortcuts, no surprises.
- 1
We walk the site and listen. Before measuring anything, we ask how you use the gate. Daily driver access, occasional ranch entrance, side yard for the trailer, guest entry. The answer changes the hardware we recommend.
- 2
We measure and mark. We check post depth, concrete condition, column construction, setback, and grade. In Keller’s clay soil, we account for seasonal movement. A gate hung to spec in July can bind in February if the posts weren’t set deep enough. We set posts below the frost line and crown the concrete at the base.
- 3
We quote the job in writing, parts and labor separate. You’ll see exactly what you’re paying for, before we turn a single bolt. The price does not change unless you change the scope.
- 4
Installation day. We bring the right hardware for the job, including OEM Elite parts where warranty matters, and quality aftermarket where it doesn’t. We hang the gate, set the automation if included, run the power properly, and set the safety edges and photo eyes to Keller’s specific code requirements.
- 5
We test like we’re the ones living behind it. Full open and close cycles, obstruction reversal, force settings, manual release. If it doesn’t close like the day it was hung, we’re not done.
- 6
Walkthrough and the 90-Day Done Right Promise. You see the gate run, you test it yourself, and we hand you the written guarantee. If it’s not right, we come back and make it right. No paperwork, no arguing.
What Elite Gate Installation Costs in Keller
Here’s what we quote on a typical Elite gate installation in Keller:
| Job Type | Typical Range |
|---|---|
| Single swing gate, manual, standard steel | $1,800 - $2,800 |
| Double swing gate, manual, ornamental steel | $3,200 - $5,000 |
| Sliding gate with Elite SL3000 automation | $4,000 - $6,500 |
| Pedestrian gate, steel, with Elite keypad entry | $1,200 - $2,200 |
| Automation retrofit on existing Elite gate | $1,500 - $3,000 |
What moves the price: gate weight and leaf size, column or post condition, whether we’re running new power, and access on the day. A gate at the back of a long Keller driveway with no nearby outlet costs more than one ten feet from the panel. The quote we give is the price you pay, every time. Call (254) 330-8718 for a free estimate.
Why Keller Homeowners Call Ironworks Gate Co. for Elite Work
We’re not the cheapest bid in Keller, and we won’t pretend to be. We’re the company you call when you want the gate done right and never want to think about it again. We’ve been serving this community for over 42 years, since 1984, and we plan to be here for another forty. Every Elite installation carries our 90-Day Done Right Promise in writing. If it’s not right, we come back and make it right. No forms, no phone tag, no fine print.
Victor Salinas grew up in Keller, learned metalwork and low-voltage systems at Tarrant County College, and has spent years working on Elite gates across DFW. He still lives a few miles from Bear Creek Park. His wife teases him that he talks about gate motors the way other men talk about trucks. After enough years of diagnosing a dead gate before opening his toolbox, he figures that’s about right. And when a Keller neighbor’s Elite gate quits the morning of a family gathering, he’s the one they call.
We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your Elite gate shares hardware with another system or you ever switch brands, our techs know what’s on the driveway. A live person answers the phone 24 hours a day, 7 days a week. No voicemail trees, no callback queues.
FAQs
No, not when the installation is done properly and with the correct hardware. What voids warranties is improper installation: wrong wire gauge, misaligned tracks, actuators mounted to loose anchors. As an independent Elite service provider, we install to the manufacturer’s specifications and document the job, so your warranty stays intact if a parts claim ever comes up.
Call (254) 330-8718 if you have a warranty question about your current Elite gate. We’ll give you a straight answer, free.
Most standard installations in Keller can be scheduled within 3 to 7 business days, depending on parts availability. If we need to special-order an OEM Elite component, that typically adds 5 to 10 days. A live person answers the phone 24 hours a day, so you’ll know your date before you hang up.
Call (254) 330-8718 and tell us what you’re installing. We’ll give you a written estimate and a firm date.
If the gate frame is straight and the posts are solid, repair is usually the better money. We’ll replace hinges, rollers, automation, or keypads and keep the existing gate. If the frame is rusted through at the welds or the posts have shifted in Keller’s clay soil, replacement usually makes more sense than pouring money into a failing structure.
Call (254) 330-8718 and describe what the gate is doing and what it is not doing. Victor can usually tell you which side of the repair-or-replace line you’re on before we even send a truck.
We use OEM Elite parts wherever the warranty or safety depends on it: control boards, actuators, safety edges, photo eyes. For hardware like hinges, rollers, and brackets, we often use quality aftermarket steel that matches or exceeds the OEM spec. You’ll always know which is which, and the price is agreed before we start.
Call (254) 330-8718 if you have a preference on parts. We’ll quote it both ways, no pressure.
Written by Victor Salinas, Owner & Gate Repair Technician, Ironworks Gate Co. at Ironworks Gate Co., serving Keller and nearby areas.