Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Motor & Opener in Keller: What to Know First
We service, repair, and install FAAC gate motors and openers in Keller, TX as an independent provider, and most repair calls are completed in a single visit. A typical FAAC repair in Keller runs between $225 and $550 depending on what has failed, with full motor replacements starting around $900. You’ll get a written quote before any work begins, and every job carries our 90-Day Done Right Promise in writing.
This page is for Keller homeowners who own a FAAC gate system and want straight answers about what goes wrong, what it costs, and who can fix it without a runaround. If your FAAC opener is acting up, call (254) 330-8718 and you’ll speak to a live person, not a voicemail tree.
How FAAC Products Fail - and How We Fix Them
FAAC builds fine motors, but like every brand, they have patterns. Here is what we see on FAAC systems in Keller, and what we do about it.
- Capacitor failure on the 400 and 402 series. The 400/402 operators are common on Keller residential gates, and the most frequent failure we diagnose is a dead start capacitor. The gate hums but does not move, or moves an inch and quits. It is a $12 part, but homeowners are sometimes quoted full motor replacement by people who did not open the cover. We always check the capacitor first.
- Limit switch drift on the FAAC 415 and 770 lines. These units use mechanical limit switches that wear and shift with temperature swings. A Keller summer followed by a cold snap is enough to make a gate stop four inches short or over-travel past the post. The gate bounces back or sits there grinding. We re-set and often replace the switch assembly; it is usually a same visit fix.
- Hydraulic pump leaks on the FAAC 400 Hydraulic swing operators. Tarrant County clay soil holds moisture, and older 400 Hydraulic units develop seal leaks at the pump after a decade or so. Owners notice a slow gate, oil on the operator base, or a gate that sags open overnight. We assess whether the seal kit fixes it or whether the piston itself is scored. We will tell you plainly if replacement beats repair.
- Control board corrosion from North Texas humidity and ants. FAAC control boards, especially the 455D and E024U, are vulnerable to tiny shorts from ant debris and condensation inside the enclosure. The symptom is erratic behavior: a gate that opens fine but refuses to close, or a keypad that suddenly stops responding. We pull the board, clean it properly, and test every input before condemning it. A surprising number of boards only need cleaning and a relay.
- Photo-eye misalignment on all FAAC swing models in Keller driveways. Keller lots are wide, and gate posts settle differently on clay depending on which side of the driveway catches the afternoon sun. When one post moves half an inch, the photo-eye beam breaks, and the gate refuses to close. We do not just realign the eye; we check what moved and shim or re-set the fitting so it stays aligned through the next soil shift.
Our FAAC Gate Motor & Opener Process
- 1
You call (254) 330-8718. A live person answers. You describe what the gate is doing, or not doing. Victor Salinas has been known to say, “Tell me what it is doing and what it is not doing - that is usually all I need to get started.”
- 2
We show up when we say we will. Our technicians are background-checked and uniformed. We work in your driveway the way we would work in our own mother’s.
- 3
Diagnosis first, quote before work. We open the operator, test the motor, capacitor, board, and limits, and lay out exactly what failed. We quote options: quality OEM FAAC parts when the repair merits it, or proven aftermarket equivalents when they serve you better. You approve the price before a bolt is turned.
- 4
The repair or replacement. Most FAAC repairs are done on the spot. If a full motor replacement is the right call, we carry common FAAC 400 and 770 series units on the truck and can typically complete replacement the same visit.
- 5
Test cycle and safety check. We run the gate through at least ten full cycles, verify sensitivity and entrapment protection, check the photo-eye and edge sensors, and confirm the manual release works without binding.
- 6
The 90-Day Done Right Promise. Every FAAC job we complete is guaranteed in writing for 90 days. If it is not right, we come back and make it right. No paperwork, no arguing.
What FAAC Gate Motor & Opener Costs in Keller
Actual numbers, because you deserve them before you call. Here is what FAAC work typically runs in Keller.
- Diagnostic service call: $89 (waived if you approve the repair)
- Capacitor replacement on FAAC 400/402: $225-$285
- Limit switch replacement and adjustment: $240-$320
- Control board repair or replacement (455D/E024U): $350-$650 depending on whether repair or replacement is the honest call
- Hydraulic oil seal service (400 Hydraulic): $300-$475
- Full FAAC motor/operator replacement: $900-$1,800 depending on model, gate weight, and whether new mounting hardware is required
What moves the price is the model, the gate’s length and weight, the age of the installation, and whether the foundation posts need work. You will always know the total before we start. Call (254) 330-8718 for a free estimate.
Why Keller Homeowners Call Ironworks Gate Co. for FAAC Work
We have been serving Keller and the surrounding communities for over 42 years, since 1984, and we plan on being here another forty. We are not a handyman service that occasionally sees a gate. We work on gates every day, and FAAC is one of nine brands we are trained on: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your FAAC system is beyond reasonable repair and a different brand makes more sense for your driveway, we will tell you that too, and we can install it.
Our word matters here. The 90-Day Done Right Promise is the Keystone Standard we apply to every job. We also answer the phone live, 24 hours a day, seven days a week. No answering service. No callback queue. And we stand behind our work with the same plainspoken certainty we have had for four decades.
FAQs
In most cases, yes. The majority of FAAC repair calls in Keller are completed in a single visit because we stock the common failure parts for the 400, 402, 415, and 770 series on our trucks. If your operator needs a part we don’t have, we will tell you before we leave and schedule the return as soon as the part lands. Call (254) 330-8718 and we will give you a straight answer about your specific gate.
We use genuine FAAC parts when the repair calls for it, and quality aftermarket equivalents when they are proven and save you money without cutting corners. We will always tell you which path we recommend and why. The 90-Day Done Right Promise applies either way.
It depends on what failed and what the motor sounds like. A capacitor or limit switch on an otherwise healthy 400 series is a repair all day long. A scored hydraulic piston or a board with multiple burned relays on a fifteen-year-old unit often points to replacement. We give you the numbers for both and let you decide. No pressure.
As an independent FAAC service provider, we are not an authorized FAAC dealer, and we will never lead you to believe otherwise. If your unit is still under manufacturer warranty, we will tell you what the warranty covers and whether a factory service call is the better financial route. For units out of warranty, which is most of what we see in Keller, our written 90-day guarantee applies.
We answer the phone live around the clock and we move quickly on security issues like a gate stuck open or a gate that will not close. Call (254) 330-8718, describe what the gate is doing, and we will get a technician to your Keller home as soon as the route allows.
If your FAAC gate motor is acting up, call (254) 330-8718. You will get a live person, an honest diagnosis, and a price before any work starts. Free estimates, every time.
Written by Victor Salinas, Owner & Gate Repair Technician, Ironworks Gate Co. at Ironworks Gate Co., serving Keller and nearby areas.