Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation in Keller: The Owner’s Guide

If you have a Ghost Controls opener on your driveway gate and the access control side has quit, here’s the short answer: we stock and install Ghost Controls keypads, push buttons, photo eyes, and receiver cards in Keller, with most access control replacements running $180 to $420 installed depending on the part, and the job is typically done in one visit. The most common call we get is a wired keypad that works intermittently after a few years of Texas sun, or a receiver board that stops recognizing remotes. You’ll want it fixed sooner than later, because when the access control fails, the gate either won’t open at all or no longer stops for a car backing out.

Call (254) 330-8718

Which Ghost Controls Models This Applies To

Ghost Controls builds their systems around two main lines: the AXDP (dual gate) and AXS series (single gate), plus the newer AXXP and TSS1 solar-friendly kits. The access control components, like the keypad (AXPK), the wireless keypad, push-button station, and the photo eye sensors (AXPE), are largely compatible across the line because Ghost Controls wired everything around a common receiver module. The gotcha we see in Keller regularly is that homeowners buy a universal keypad from a big-box store and learn the hard way that Ghost Controls uses a proprietary four-wire protocol; a generic keypad will not talk to the board. If you’re replacing a photo eye, measure the mounting post spacing first: Ghost Controls sensors use a fixed bracket width that does not line up with LiftMaster or Mighty Mule sensor brackets. We’re an independent service provider, not affiliated with Ghost Controls, but we keep OEM and quality aftermarket equivalents on the truck for the AXS and AXDP series because that’s what’s installed on most Keller driveways built in the last ten years.

How to Identify Your Ghost Controls Part

Before you call, pop the cover off the control box. Look for a white label with the model number, usually starting with “AX” or “AXDP.” On the keypad itself, Ghost Controls stamps the part number on the back plate. If you can’t find the number, count the wires coming into the part: four wires means it’s a Ghost Controls native component, not a generic replacement. That one detail saves us a return trip and saves you the cost of a part that was never going to work.

Signs Your Ghost Controls Access Control Installation Is Failing

• Keypad beeps but the gate doesn’t move. The keypad is sending the access code, but the receiver on the control board isn’t relaying it to the motor. We see this most often on boards older than five years, and the fix is usually a receiver card or a full board swap, not a keypad replacement.
• The gate opens fine with the remote but not the keypad. This isolates the failure to the keypad or its wiring. In Keller, the usual culprit is moisture intrusion at the keypad base, especially on west-facing posts that catch the afternoon storms.
• Photo eyes flash or the gate reverses for no reason. Ghost Controls photo eyes are sensitive to misalignment and to dusty lenses. North Texas wind and construction dust coat the lenses quickly, and the gate will misbehave even when the eyes look fine.
• The gate won’t close on auto-close, but works manually. That almost always traces back to a failing photo eye circuit or a loose connection at the board, not the motor or the arm.
• Remotes work one day, then not the next. Ghost Controls receiver boards can develop cold solder joints after a few years of Keller temperature swings, those hundred-degree afternoons and fast fall cold fronts. The fix is a board-level repair or a replacement receiver, depending on what we find.

Replacement Cost & What’s Included in Keller

For Ghost Controls access control work in Keller, here’s what you’re looking at:

• Wired keypad replacement: $190 to $340 installed (OEM or quality aftermarket part plus labor)
• Wireless keypad replacement: $210 to $360 installed
• Photo eye pair (sensors and wiring check): $180 to $310 installed
• Receiver board or control board replacement: $260 to $420 installed
• Push-button station or intercom-style entry: $180 to $280 installed

Every quote includes the part, the labor, and a full function check of the whole system, not just the part we replaced. We settle the price with you in writing before a single screw comes out. If we find an aftermarket equivalent that matches the OEM spec and saves you money, we’ll tell you; if OEM is the only thing that’ll hold up, we’ll tell you that too. The work is covered by our 90-Day Done Right Promise, written, no arguing, no fine print.

DIY or Call Us?

There’s an honest split here. You can safely check a few things yourself: make sure the keypad has power, clean the photo eye lenses with a dry cloth, and confirm the wires at the back of the keypad are still tight. That’s where it stops. Ghost Controls access control runs on low-voltage DC, so you’re not dealing with line current, but the control board is the brain of the whole gate; one crossed wire at the receiver terminal can burn a board that costs as much as the service call to fix it right. We’ve had Keller homeowners hand us boxes of parts they bought trying to avoid a service fee, and the total cost ended up higher than if we’d come out first. If the gate is doing anything except working perfectly, call (254) 330-8718 and tell us what it is doing and what it is not doing, that’s usually all we need to get started.

Frequently Asked Questions