Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Repair in Keller: What to Know First
Linear gate repair in Keller runs between $185 and $640 for most residential jobs, depending on whether we’re replacing a control board, a swing-arm actuator, or rewiring a failing photo eye. We’re an independent Linear service provider, not a factory warranty center, and we complete most repairs in a single visit because we stock the parts that actually fail on Linear systems in North Texas. If your gate is stuck, grinding, or beeping at you, call (254) 330-8718 and tell us what it’s doing and what it’s not doing - that’s usually all we need to get started.
This page covers the Linear operators and gate hardware we see in Keller driveways: the ACT/Swing series, LRA linear ram actuators, and the APeX and MegaCode controllers that run them.
How Linear Products Fail - and How We Fix Them
- Dead control board on APeX-equipped swing gates. Keller gets some honest heat, and heat is hard on the electrolytic capacitors on APeX controller boards. The gate works fine all winter, then quits in August. The board shows no LED, no click when a remote is pressed. We replace the board, check the surge protection, and move on. This is the single most common Linear failure we walk up to in Keller.
- LRA linear ram actuator making noise but not moving the gate. The LRA series uses a threaded screw inside the ram body. When the internal nut strips, the motor spins and the gate stays put. Homeowners describe it as a grinding or humming sound. The fix is a new internal carriage assembly or a full ram replacement, depending on mileage and how long the gate has been binding before the stripping happened. We always check the hinge posts for sag when we find a stripped ram - the actuator usually wore out because the gate was fighting its own weight.
- MegaCode receiver losing remotes after a power surge. Lightning is a regular visitor in Keller. A nearby strike can dump voltage through the low-voltage control wiring and wipe the receiver’s stored codes. The gate still works from the hardwired keypad, but every remote stops responding. We reprogram, add surge suppression, and in some cases install a receiver with more code memory if the homeowner has a multi-remote household.
- Photo eyes misaligned on the SWD swing gate series. The swing gate arms rotate on posts that shift with our clay soil and freeze-thaw cycles. A post that moves a quarter inch takes the photo eye beam out of line by just enough to trip the gate into sensor-fault mode. The gate reverses, stops, and the control board blinks a trouble code. We realign the posts before we even touch the sensor bracket, because adjusting the eye against a leaning post just moves the problem down the road.
- Warning buzzer or alarm sounding with no obvious cause. On Linear’s auto-close systems, the audible alarm usually means the entrapment detection circuit is seeing a fault. That can be a pinched wire, a failing edge sensor, or a motor drawing more current than the board expects. We trace it with a meter rather than disconnecting the buzzer - a quiet gate that hasn’t been fixed is a dangerous gate.
Our Linear Gate Repair Process
- 1
You call, a person answers. We note the model, the symptom, and when the gate last worked right. Often Victor Salinas has a good idea what’s wrong before we roll the truck, because he’s been working on these in Keller for a long time.
- 2
We arrive, confirm the diagnosis, and quote the price. No work starts until you know the number. That number is the number, whether the job takes forty minutes or three hours.
- 3
Parts go in. We use Linear OEM boards, rams, and receivers when they’re available and make sense. When OEM lead times are unreasonable or a part has a known short lifespan, we’ll tell you and offer a quality aftermarket option with the honest trade-off spelled out.
- 4
We test the full cycle. Open, close, obstacle detection, photo eyes, keypad, remotes, auto-close if you have it. We run the gate through at least a dozen cycles before we call it done.
- 5
We walk the site with you. You see what we changed, what we checked, and what still looks tired. We don’t leave you guessing.
- 6
Everything gets the 90-Day Done Right Promise. Written, simple, no paperwork chase. If it’s not right, we come back and make it right.
What Linear Gate Repair Costs in Keller
Here’s what we charge for the common Linear jobs in Keller:
- Diagnostic visit: $89 - waived entirely if we do the repair on the same visit.
- Photo eye realignment or replacement: $185-$260
- MegaCode receiver replacement and remote reprogramming: $210-$320
- APeX control board replacement: $340-$520
- LRA ram actuator rebuild or replacement: $480-$640
- Full swing gate service, both operators, hinges and limit tuning: $600-$850
What moves the price is mostly parts cost and whether the gate needs structural work alongside the electrical repair. A stripped gate hinge is a $25 part with an hour of welding behind it. A ram that failed because the post rotted at the base is a bigger conversation. You’ll know the exact number before we turn a single bolt. Call (254) 330-8718 for a free estimate.
Why Keller Homeowners Call Ironworks Gate Co. for Linear Work
Over 42 years in this trade and this town, we have learned something straightforward: homeowners don’t want a gate repair story, they want a gate that works. That’s why we keep Linear parts on the truck, why our techs are trained on nine major opener brands - LiftMaster, Mighty Mule, Ghost Controls, and DoorKing included - and why a live person answers the phone at (254) 330-8718 at any hour. If your Linear actuator is down and we find the real fix is a different brand’s board because someone before us made a Frankenstein of it, we handle that too. One visit, done right, backed in writing.
Every job ends the same way: the 90-Day Done Right Promise. A square deal, no surprises on the bill, and a company that plans to be in Keller for another forty years.
FAQs
No. As an independent Linear service provider, we are not an authorized warranty center, and repairs we perform on out-of-warranty systems do not affect any remaining coverage on other components. If your Linear gate is still under factory warranty, we will tell you before any work begins and recommend you contact the manufacturer directly for that specific part.
In most cases, yes. Common repairs like photo eyes, receivers, and control boards are parts we keep on the truck in Keller, so they’re handled in a single visit. Ram actuators sometimes require a part we need to order, depending on the model, and we’ll give you an honest timeline before any work is scheduled. Call (254) 330-8718 and we will tell you what’s realistic for your specific system.
It depends on whether the gate itself is still solid. If the posts are straight and the gate is square, a new board or actuator can easily buy another five to ten years. If the metal is fatigued, the hinge weld is cracked, and the opener is struggling against a gate that no longer hangs right, a repair just postpones the inevitable. We’ll give you our straight answer on the driveway, and the quote either way is free.
We use OEM Linear parts when they’re available at reasonable lead times. When an OEM part is backordered or has a known failure pattern we’ve seen repeatedly in Keller’s heat, we’ll offer a quality aftermarket alternative and explain the difference before we install it.
Usually, yes, though it depends on the model and age of the receiver. Older MegaCode systems share code technology with newer units more often than not, so we can often swap the receiver and reprogram your existing remotes on the spot. If your remotes are too old to pair, we’ll tell you and include that in the quote before any work starts.
Written by Victor Salinas, Owner & Gate Repair Technician, Ironworks Gate Co. at Ironworks Gate Co., serving Keller and nearby areas.