Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Aurora
A gate that drags, sags, or will not latch in Aurora is rarely a simple hinge problem. The ‘black waxy’ clay under Wise County expands and contracts with every rain and drought cycle, heaving gate posts out of square and turning a minor hinge issue into a full post reset. We send a technician who checks the footing first, because on an Aurora ranch entry the soil under the post is where the trouble starts. Call us at (254) 330-8718 and we will walk the gate with you before turning a single bolt.
Why Ironworks Gate Co. Is Aurora’s Preferred Gate Parts & Welding Company
Aurora properties are not Fort Worth’s. They are wide ranch entries on caliche drives, shared creek crossings on County Road 4290, and double-swing tube-steel gates that get hit by the same west wind that rattles the windmills. The gate work here takes somebody who has re-welded a hinge on a cattle gate that weighs more than a compact car, and then set the posts deep enough to hold through a wet winter. That is the work we do, and we have done it since 1984.
We answer the phone like a neighbor because our Aurora customers do not want to chase a call center. When you call, a live person picks up, 24 hours a day. The technician who arrives is background-checked, uniformed, and carrying the exact hinge brackets, roller bearings, and latch parts for your gate, not a generic truck stocked for a different county. We quote the work before we start, and every job carries our 90-Day Done Right Promise in writing.
Victor Salinas leads our team with one standing rule: assess the post and the footing before touching the hardware. That rule exists because of Wise County clay, and it is why an Aurora gate fixed by us stays square longer than one patched by a crew that does not know the soil.
Our Gate Parts & Welding Services in Aurora
Our Gate Parts & Welding team handles the full metalwork scope on a ranch gate: hinges, posts, rails, custom fabrication, rollers, latches, and locks. Here is what that looks like on an Aurora property.
Hinge Replacement
Wind fatigue kills hinges faster on open Aurora ranch entries than anywhere with tree cover. We see pins worn into an oval, hinge ears cracked at the weld, and gates that have sagged until the latch post catches the corner. We replace hinges with greasable barrel hinges or weld-on adjustable hinges sized for the gate’s actual weight, not whatever was on the shelf. Most hinge replacements in Aurora run $120 to $240 per hinge, installed with the gate off its load.
Post Replacement
This is the Aurora special. The expansive clay heaves posts until the whole gate tilts, and no hinge adjustment will fix a leaning post. We dig the old footing, re-bed with compacted road base or concrete depending on the soil at your site, and weld or bolt the new post plumb. A residential or light ranch post replacement here typically runs $300 to $650 per post. For heavy double-swing entries, figure $600 to $1,000 per post with cross-bracing and fresh footings, and we always set the post deeper than the frost line and the heave zone.
Rail Repair
Tube-steel top and bottom rails crack at the weld joints after years of wind load and cattle pushing against the gate. We cut out the fatigued section, weld in a new rail or fish-plate the crack, and re-hang so the gate does not twist. Expect $90 to $200 per rail section depending on length and whether we are working on a single swing or a long double leaf. On a rusty or thinned rail, the honest fix is full replacement, and we will show you the metal before we recommend it.
Custom Welding
Sometimes a gate needs something that was never a stock part. We weld custom hinge tabs, wheel-mount plates for slide gates, latch extensions, and patch sections for rusted tubing. We also build entire gate frames to match an existing fence line. Custom welding on an Aurora gate starts around $120 for small brackets and tabs, up to $500 or more for fabricating a new double-swing frame by hand. Victor welds every custom job himself when the geometry is unusual.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Aurora
Aurora ranches run a mix of old and new openers. We are certified on FAAC and BFT for heavy hydraulic and electromechanical operators on the big swing gates, plus Viking and Linear for newer slide and solar installations. We keep hinge brackets, end-stop brackets, and latch hardware for those brands on the truck so a ranch gate does not sit down for days waiting on a part. If your operator is wearing out a hinge because it is out of square, we fix the alignment and the metal together.
Common Gate Parts & Welding Problems We See in Aurora Homes
- Wind-thrown double swings. Sustained wind leans the top of the gate away from the hinge post, so the latch ends up an inch or two too low to catch. The pins and ears wear egg-shaped, and then the gate starts dragging on the caliche. Hinge replacement and a sag correction bring it back square.
- Clay-heaved hinge posts. One wet winter on Wise County’s expansive clay can lift a post two inches or more. The gate jams at the latch post, or the hinge side rises until the gate binds. We re-set the post and weld any cracked footing brackets while the hole is open.
- Shared driveway failures. On Aurora’s shared ranch drives, one down gate blocks everyone. A broken slide-gate roller or a snapped latch on a swing gate strands vehicles on either side. We get the opening working again and repair the failed part rather than patching around it.
- Fatigued welds on tube-steel frames. The welds at rail-to-hinge and rail-to-latch joints crack from years of wind and daily use. The gate gets a bow in it, then a twist. We cut out the old weld, prep the steel, and lay a stronger fillet with full penetration.
Pricing for Gate Parts & Welding in Aurora, TX
A hinge replacement in Aurora runs $120 to $240 per hinge. A post replacement runs $300 to $650 for a standard ranch post, and $600 to $1,000 for a heavy double-swing post with new footing. Rail repair is $90 to $200 per rail section, and custom welding starts around $120 for a small bracket and climbs with the size of the fabrication. Those are real numbers for this part of Wise County, quoted before the work starts. The variables are the gate’s weight, the condition of the post footing, and the access around the hinge side, which we confirm on site. Every estimate is free, and the price you approve is the price you pay. We do not surprise anyone.
Keep the standing offers in mind: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and 5% off for seniors and veterans. Call (254) 330-8718 for an exact quote on your gate.
We Also Serve Cities Near Aurora
We handle Gate Parts & Welding in Aurora and the surrounding Wise County and Denton County communities. That includes Keller, Haslet, Newark, and New Fairview. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and crews serve Aurora locally.
Serving Aurora, TX - Our Local Coverage Area
We’re based in the Aurora area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Aurora
Because the hinge post has likely heaved on the clay. Adjusting hinges only changes the gate’s angle on the post; it does nothing for a post that is leaning or has risen out of its footing. In Aurora we check post depth and plumb first, and most dragging gates need a post reset before the hinge holds a correction. Call (254) 330-8718 and we will check the footing at no charge.
Usually yes. We can jack the gate level on its hinge side, weld the broken bracket or hinge ear in place, and re-align the gate without removing the leaf from the post, as long as the post footing is sound. If the post has heaved, the gate has to come down for a proper reset, and we will tell you before we touch it. Call (254) 330-8718 for a free on-site look.
We pull the gate off the hinge side, set it on blocks or a temporary brace, and leave the latch side clear so vehicles can still pass while the new footing cures. Most shared-driveway post replacements in Aurora are done in one day, and traffic keeps rolling. Call (254) 330-8718 and we will talk through the access for your drive.
In most Aurora ranch entries, yes. A slide gate has no long hinge line for the wind to lean on, and its top guide holds the leaf against wind load. The weak point becomes the roller bearing and the track, which we check and replace as a pair. But a slide gate needs the side clearance to roll. On tight entries where that is not available, a properly built swing gate with greasable heavy hinges still works; it just needs sag correction more often. Call (254) 330-8718 and we will measure your entry and give you a straight recommendation.
If it is an automatic gate, yes. Photo-eyes are a required safety device that stops and reverses the gate if a person, vehicle, or animal breaks the beam while the gate is moving. On Aurora ranch entries, we often mount them on steel posts offset from the gate path so livestock do not knock them out of alignment. Victor can test your existing photo-eyes and wire in a replacement the same visit. Call (254) 330-8718 for a safety check.
Call Ironworks Gate Co. for Gate Parts & Welding in Aurora
When a gate will not hold square in Aurora, call the shop that knows Wise County clay and wind. We quote the work upfront, in writing, before a single bolt turns. Every completed job is covered by the 90-Day Done Right Promise, and a live person answers the phone day or night. Call (254) 330-8718 for a free estimate, or to have Victor look at your gate this week.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Aurora and Wise County gate owners since 1984.