Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Aurora, TX | Ironworks Gate Co.
If your Ghost Controls opener is stalling mid-cycle, blowing fuses, or throwing error codes after every rain, we can fix it. Ironworks Gate Co. provides independent Gate Repair in Aurora for Ghost Controls systems, and the one thing that sets our work apart here is simple: we check the post and the footing before we touch the opener. That matters in Aurora more than almost anywhere else in North Texas because of what the soil does. Call (254) 330-8718 and tell us what the gate is doing and what it is not doing – that is usually all we need to get started.
Why Aurora Residents Choose Us for Ghost Controls Service
We have repaired hundreds of Ghost Controls gate openers across Wise County, from AXDP and TSS1 linear arm openers on ranch swing gates to the more complex FPW series on wide double-gates. Our techs know which models hold up to North Texas wind and which need proactive reinforcement before they fail. That experience came the hard way – over 42 years of gate work in this country, learning what the wind, the clay, and the sun do to steel and circuitry.
Victor Salinas runs our Ghost Controls service work, and he grew up in Keller, learned metalwork and low-voltage electrical systems at Tarrant County College, and spent years working alongside gate tradesmen across the DFW area before planting roots with Ghost Controls sales & service at Ironworks Gate Co. He understands that an Aurora gate is not a suburban ornament – it is a working piece of ranch infrastructure. We are an independent Ghost Controls service provider, not manufacturer-affiliated, which means we fix what is actually wrong rather than pushing a replacement the factory would prefer. And every job is backed by our written 90-Day Done Right Promise. If it is not right, we come back and make it right. No arguing.
Common Ghost Controls Gate Repair Problems We Solve in Aurora
- Stripped AXDP gears from wind gusts. The AXDP is a high-torque single arm opener, but a 50-mph gust hitting a 14-foot pipe gate mid-cycle can strip the internal gear. Aurora’s open, wind-exposed acreage properties with little windbreak on the north side make this a recurring call for us. We stock OEM gear kits for quick turnaround.
- TSS1 limit loss after heavy rain. The TSS1 control board intermittently loses its open/close limits after significant rainfall. In Aurora, that is not a fluke – black waxy clay swells and shifts posts, altering the gate’s travel path. The board is not always the problem; the post is. We diagnose both before quoting.
- FPW wheel slippage on caliche and gravel. The FPW is a wheel-drive opener for sliding and cantilever gates, but on dusty caliche driveways – common throughout Aurora’s ranch properties – the drive wheel loses traction, the gate stops short, and you are recalibrating every few weeks. We have a fix that does not require paving your driveway.
- Clouded keypads refusing codes. Factory keypads on older AXDP and TSS1 units cloud over from UV exposure and hard water. In Wise County’s summer sun, that happens faster than the manual suggests. The keypad may still be usable; the lamination is what fails. We replace the pad, not the whole opener.
- Post lean throwing the gate out of square. This is the Aurora signature problem. Expansive clay heaves a post 2-3 inches in a wet winter, the gate binds, and the opener fights the hinge every cycle. We reset posts below the moisture variation line and verify the gate swings true before recalibrating any Ghost Controls opener.
Ghost Controls Service in Aurora: What Local Conditions Mean for Your Equipment
Aurora sits on the ‘black waxy’ expansive clay of the Fort Worth Prairie. This soil can heave a correctly-set gate post 2-3 inches in a single wet winter – not over decades, but in one season. We will not touch a Ghost Controls opener until we have uncovered the post footing and verified it is below the moisture variation line. Skip that step and the gate is out of square again before the next rain. It is a lesson we learned years ago on a job off County Road 4680, and it applies to nearly every Aurora Gate Installation we do in unincorporated Aurora. The wind is the other factor. Wise County sits in the open North Texas plains, and sustained high winds accelerate hinge fatigue and throw gates out of plumb far faster than in sheltered urban areas. A Ghost Controls opener that runs perfectly in a Fort Worth subdivision may struggle out here within two years – not because the opener is weak, but because it is fighting wind load and shifting posts every single cycle. Our job is to remove the fight, then let the opener do what it was built to do.
Ghost Controls Models & Products We Service in Aurora
We service the full Ghost Controls line as it exists on Aurora properties: the AXDP high-torque single arm for standard ranch swing gates, the TSS1 dual arm for heavier 16-foot-plus pipe gates, the FPW wheel-drive for sliding and cantilever gates, and the DSL1 pull-to-open for lighter farm gates. Our approach on parts is straightforward: we use OEM Ghost Controls control boards, motors, and limit switches whenever available because the aftermarket equivalents often run hotter and fail faster in Wise County’s summer heat. For $12 hinge bushings or $30 solar trickle chargers, we will recommend a quality aftermarket part if it clearly extends service life. And if the gearbox has already eaten itself on an opener that is 8+ years old, we will tell you straight that a new opener is cheaper than rebuilding the old one. That honesty is how we have kept customers in Aurora for over four decades.
Ghost Controls Service Pricing in Aurora
Service calls in Aurora typically start around $89 for a basic diagnostic and tune-up, with most Ghost Controls repairs landing between $180 and $450 depending on parts and the amount of post work involved. A full opener replacement, including new hardware, wiring, and post reset, generally runs $850 to $1,600. What drives the price here is the same thing we keep coming back to: post condition. If the clay has moved the post, we have to fix that before the opener repair is worth doing. Every quote includes a written breakdown, agreed before work starts – you will not open an invoice that surprises you. Call (254) 330-8718 for a free estimate. We also honor a $50 discount on any repair over $250 and a 5% senior and veteran discount, always.
Serving Aurora, TX - Our Local Coverage Area
We’re based in the Aurora area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Aurora
The error is usually not the opener’s fault. Aurora’s black waxy clay swells when wet, shifting your gate post and altering the travel path. The AXDP sees resistance it was not calibrated for and throws a fault. We reset the post below the moisture line and recalibrate the limits – the fix usually holds through the next storm. Call (254) 330-8718 and describe what the gate does after rain; that is often enough for us to diagnose it over the phone.
Yes. FPW wheel-drive units develop slippage on dusty caliche and loose gravel, causing the gate to stop short. We realign the drive wheel, clean and tension the track assembly, and in many cases add a traction sleeve that grips without damaging the opener. It is a common fix for Aurora ranch drives. Call us for a free estimate.
No. The keypad on older AXDP and TSS1 units is a separate component. UV and hard water cloud the face until the buttons stop registering. We replace the keypad with a new OEM or compatible unit, reprogram it, and the opener itself stays in place. That repair usually takes under an hour.
No, and that knock is worth addressing quickly. On a TSS1 or AXDP in Aurora’s open wind conditions, a loud knock usually means the gate is binding against a shifted hinge or the post has started to lean under wind load. The opener is absorbing stress it should not. We realign the gate and reinforce the hinge – ignoring it will eventually strip the gear or burn the motor.
We set Aurora gate posts at least 36 inches deep, and often 42 to 48 inches for wide double-swing ranches, in a concrete footing that reaches below the moisture variation line. That depth is the difference between a gate that holds square through a wet winter and one that heaves out of plumb by March. If your post is shallower than that, we will probably recommend a reset before calibrating any Ghost Controls opener. Call (254) 330-8718 and we will come look.
Service Areas Near Aurora
Ironworks Gate Co. serves Aurora and the surrounding Wise County communities, including New Fairview, Newark, Pecan Acres, and Haslet. For Ghost Controls owners in the Keller area, we offer the same factory-familiar service through Ghost Controls service in Keller. If you are a few miles north, see Ghost Controls service in Haslet. Our full Aurora service area page has the details.
Book Your Ghost Controls Service in Aurora Today
A live person answers our phone 24 hours a day, 7 days a week – no voicemail trees. Call (254) 330-8718 now and describe what the gate is doing. We will give you a straight answer, a free estimate, and if the job is urgent, we can often have a technician on your Aurora property the same day.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Aurora and Wise County since 1984.