Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Bedford
Gate repair in Bedford usually costs between $160 and $480 depending on what failed, and most hinge, post, and latch repairs are done in a single visit. If your gate drags on the driveway, won’t latch, or the opener stopped responding, we can usually have a technician at your Bedford home within a few hours. Call (254) 330-8718 and a live person answers, day or night.
We know Bedford’s gates because we see them every week: original wooden privacy gates from the 1975-1993 building boom, wrought-iron driveway gates near Central Drive, and operators that predate modern safety sensors. That local familiarity means we diagnose faster and quote accurately, and the price is settled before we turn a single bolt.
Why Ironworks Gate Co. Is Bedford’s Preferred Gate Repair Company
We’ve been repairing gates for over 42 years, and in that time we’ve watched Bedford’s original gates age right alongside the neighborhood trees. The work here is almost entirely rehabilitation, not new installs. That’s a different kind of expertise than a builder who frames new gates all day. Knowing how a 40-year-old post-and-panel installation behaves after three decades of Tarrant County clay movement, that’s the knowledge that keeps a repair from failing two months later.
Bedford homeowners call us because we send background-checked, uniformed technicians who respect the home and explain exactly what they found and what they propose to do about it. Every job is covered by the 90-Day Done Right Promise, in writing. If it’s not right, we come back and make it right. No paperwork, no arguing. That’s the standard our founder, Victor Salinas, built the company around, and it holds for every job in the 76021, 76022, and 76095 ZIP codes.
Our Gate Repair Services in Bedford
We handle the full scope of gate work, but in Bedford, four services carry most of the load. Here’s what we actually see and what we do about it.
Hinge & Post Repair
Bedford’s clay soil is the root cause of most hinge and post failures. When a post tilts, the gate panel hangs crooked and the hinge screws start pulling loose. We reset posts in properly sized concrete footings, replace corroded hinges with new hardware rated for the gate’s weight, and rehang the panel so it swings clean. This is the most common repair we perform in Bedford, and it’s the one that benefits most from doing it right the first time.
Gate Realignment
A gate that drags or won’t latch is almost always a realignment problem, not a reason to replace the whole gate. Seasonal soil movement tilts the hinge post a few degrees, and suddenly a gate that closed fine in April is carving a crescent into the grass by August. We true the posts, adjust the hinges, and set the latch so it holds through the next wet-dry cycle. In Bedford, where the clay shrinks and swells more aggressively than in newer suburbs on engineered fill, this is a recurring seasonal service for many homeowners.
Weld & Rust Repair
Wrought-iron driveway gates in established Bedford neighborhoods, especially around Harwood Road and the older lots near Central Drive, show their age at the hinges and latch points first. Rust creeps in, weakens the metal, and eventually the gate sags or a hinge bracket cracks. We grind out the rust, weld the broken members, and re-coat the area so it holds. If the frame is too far gone, we’ll say so honestly and quote a replacement rather than a repair that buys you another season.
Lock & Latch Repair
Gate latches take the most abuse of any component. When a post shifts even slightly, the latch no longer lines up with the strike plate, and the gate won’t stay closed. We align the latch, replace worn hardware where needed, and test the gate through a full swing arc before we leave. A gate that latches properly is a security issue settled, and it’s one of the fastest fixes we do.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Bedford
We’re certified on nine major gate-automation brands, so whatever is on your driveway, we’ve seen it before. FAAC, BFT, Linear, and Viking are common on Bedford’s original installations, and we carry the parts and control boards that local supply houses stopped stocking years ago. That matters: a 1987 FAAC opener doesn’t need a new motor just because the control board failed. We can often retrofit modern safety sensors and replacement boards into legacy housings, which costs hundreds less than a full system replacement. See our Gate Repair page for the full brand list.
Common Gate Repair Problems We See in Bedford Homes
- Late-summer dragging and misalignment. Every August and September, Bedford gates that worked fine in spring begin dragging on driveways or failing to latch. It’s the expansive clay contracting after months of drought, tilting posts that were set in shallow footings decades ago. The gate didn’t break; the ground moved under it, and the fix is a proper post reset, not a new panel.
- Rusted hinges and latches on wrought-iron gates. Original driveway gates from the 1980s and early 1990s are now 35-50 years old, and the hardware is corroding. We see this consistently in the established sections near Central Drive and Harwood Road, where original iron gates hang on original hinges. The repair is hinge replacement and, where needed, welded reinforcement at the hinge brackets.
- Obsolete operator control boards. Many Bedford homes still run the operator that was installed when the house was built. When the board fails, homeowners are quoted a full replacement by generalist companies that don’t stock legacy parts. We can often source or retrofit a compatible board and add modern safety sensors, extending the operator’s life without a full swap.
- Warped wooden gate frames. Original cedar and pressure-treated pine privacy gates absorb decades of North Texas freeze-thaw and spring storm cycles, and the frames twist. When the frame is warped but the hardware is sound, we can sometimes straighten and reinforce it. When the frame is gone, we’ll say so and quote a rebuild that matches the existing fence line.
Last August, our crew realigned a swing gate on a 1980s ranch home off Central Drive where the original cedar panel dragged a full two inches across the driveway. The hinge post had tilted inward after months of summer drought contracted the clay around its footing, and the top hinge lag screws were pulling loose. We reset the post in a deeper concrete footing, replaced the corroded hinges, and adjusted the latch to hold true before the fall rains set in. That’s the work this page is about: understanding why a Bedford gate fails, then fixing the cause, not the symptom.
Pricing for Gate Repair in Bedford, TX
Here are honest numbers for the Bedford market. A hinge and post reset typically runs $180-$340 per post, depending on whether the post needs a new concrete footing or can be trued in place. Gate realignment, including hinge adjustment and latch setting, usually runs $120-$220. Weld and rust repair on a wrought-iron gate starts around $150 and can reach $450 for extensive frame repair and re-coating. Operator control board replacement, including the part, runs $280-$520 on most legacy units.
What moves the price: how far the post has tilted, whether the concrete footing needs to be excavated, and how much rust has gotten into the hinge brackets. You’ll get a written quote before any work starts, and that number doesn’t change without a phone call first. We also run standing offers for Bedford residents: $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% discount for seniors and veterans. Call (254) 330-8718 and we’ll walk you through it. For the broader service picture, see Gate Repair in Bedford.
We Also Serve Cities Near Bedford
Our crews handle gate repair throughout the Mid-Cities. We regularly serve homeowners in Hurst, Colleyville, North Richland Hills, and Southlake, and we’re familiar with the same soil conditions and housing stock patterns that affect Bedford. Dispatch is coordinated from our Dallas-Fort Worth office, and Bedford-area calls get a local crew.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Bedford
The clay soil under your fence posts shrinks during the long dry summer, which causes the hinge post to tilt and the gate panel to lose clearance. This is predictable in Bedford, and the fix is resetting the post in a deeper concrete footing rather than trimming the gate panel. Call (254) 330-8718 for an exact assessment.
In most cases, yes. We can replace an obsolete control board and add photo-eye safety sensors without replacing the entire operator. The board and sensors typically run $280-$520 installed, and the work is usually completed in one visit. We stock boards for FAAC, BFT, Linear, and Viking systems found on Bedford’s original installations.
If the post has been straightened once and is leaning again, the footing is undersized for Bedford’s expansive clay. The correct fix is excavating and pouring a deeper concrete footing with proper drainage, which typically runs $180-$340 per post. Straightening without addressing the footing is a temporary fix that will fail again. We’ll quote both options honestly and let you decide.
Not always. If the frame is warped but structurally sound, we can often reinforce it and replace the hinges. If the frame is rotted or the metal is too thin at the hinge points, replacement is the cheaper long-term answer. We’ll tell you which one applies to your gate before any work starts, with a written price in hand.
The telltale signs are intermittent operation, a humming motor that won’t move the gate, or a board that no longer responds to remotes or keypads. If the system predates photo-eye safety sensors, it’s original equipment and the board is likely end-of-life. We can test the board on-site and quote a retrofit if it’s obsolete. Call (254) 330-8718 and we’ll schedule a diagnostic.
Call Ironworks Gate Co. for Gate Repair in Bedford
If your gate is dragging, sagging, won’t latch, or the opener stopped working, call (254) 330-8718. A live person answers 24 hours a day, 7 days a week. We’ll get a technician to your Bedford home, diagnose the problem, and give you a written price before any work begins. Every job is backed by the 90-Day Done Right Promise. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Bedford from our Dallas-Fort Worth office.