Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Keller Homeowners
A gate is only as strong as its weakest weld and its smallest part. When a hinge sags, a post shifts, or a rail separates, the whole gate loses its line, drags on the ground, and eventually stops closing at all. Gate Parts & Welding - Keller is the repair that gets a heavy driveway gate hanging square, swinging smooth, and latching tight again. Ironworks Gate Co. has been doing exactly this work for over 42 years, and Victor Salinas and his team handle everything from a single hinge replacement to a full structural rebuild, right here in Keller. If your gate is binding, sagging, or clanking, call (254) 330-8718 and we will come take a look.
What Our Gate Parts & Welding Service Includes
Most gate failures trace back to one of six common points: hinges, posts, rails, welds, rollers, or latches. Here is what we do for each one, and how you will know when it is time to call.
Hinge Replacement
Hinges carry the entire weight of the gate, every single day, in Keller heat and Keller storms, which is why we offer the Best Gate Parts & Welding in Keller, TX. When a hinge barrel wears out or a leaf bends, the gate drops on the latch side and you will see a widening gap at the top or bottom. We remove the old hinge, weld a new one in place, and set the gate back to its original height. On heavy steel and ornamental iron gates, we use greasable hinges so the next forty years are quieter than the last.
Post Replacement
A leaning gate post is almost always a sign that the original post was set too shallow, or that years of wind load have worked it loose in the soil. In Keller’s clay-heavy ground, posts set without enough concrete or without a proper footing will shift with the wet and dry cycles. We cut out the old post, dig a deeper footing, set a new steel post in concrete, and weld the gate back to it. The gate ends up plumb, square, and solid in its opening.
Rail Repair
The top and bottom rails are the gate’s backbone, and when one rusts through or separates at a weld joint, the gate loses its structural integrity. You may notice the gate flexing in the middle when it moves, or a visible crack in the rail. We cut out the compromised section and weld in new steel, then grind the repair smooth and repaint it to match. A rail repair done correctly is invisible and stronger than the original.
Custom Welding
Not every gate problem has an off-the-shelf answer. Sometimes you need a section rebuilt, a decorative element reattached, or a custom bracket fabricated to mount a new opener. Our welders work in steel, aluminum, and wrought iron, including ornamental scrollwork that has to match the existing design. If it is metal and it needs to hold, we can cut it, shape it, and weld it in place, and it will look like it was always there.
Gate Rollers
Sliding gates run on rollers, and worn rollers are the most common reason a sliding gate starts to grind, jump the track, or refuse to move without a fight. We carry replacement rollers in multiple sizes and weight ratings, including heavy-duty sealed bearing rollers for gates over 400 pounds. We replace the rollers, inspect the track for wear, and adjust the gate so it rolls with one hand.
Latch & Lock
A latch that does not catch is a gate that does not stay closed, and a lock that is seized is a gate that cannot be secured. We repair and replace mechanical latches, magnetic locks, drop rods, and keyed locks on gates from every era. Whether it is an original hardware set on a forty-year-old ornamental gate or a modern keypad-controlled lock, we fix it so it closes soft, latches firm, and locks tight.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
Most gate hardware on the market today is built to work with specific opener systems, and we see a lot of FAAC and BFT equipment in Keller driveways. These Italian-built systems are common on newer estate gates, and we know their mounting patterns, their hinge requirements, and where they tend to fail when a gate is out of alignment. We keep the OEM parts and the fabrication knowledge to repair the gate itself, not just the operator mounted to it.
We also work regularly on Linear and Viking systems, which are common on older homes in established Keller neighborhoods. The operators are reliable, but the steel underneath them ages, and a new opener cannot fix a sagging hinge or a cracked weld. Whether you have FAAC, BFT, Linear, Viking, or any other make, we can match the parts and the welding to what is already on your driveway.
Signs You Need Gate Parts & Welding Right Now
- The gate drags or scrapes on the ground. A sagging gate is a hinge or rail problem, and every scrape is grinding metal away. Left alone, it eventually bends the gate frame and makes the repair twice as expensive.
- You can see a gap at the top or bottom of the closed gate. That gap means the hinges are wearing or a post is moving. The gate is no longer square in its opening, and the strain is transferring to the opener motor.
- The gate shakes or flexes when it moves. A gate that flexes in the middle has a cracked rail or a separated weld. The metal is working against itself on every cycle, and the crack gets longer every time the gate opens.
- You hear grinding, clanking, or metal-on-metal noise. Noise is the sound of wear. Rollers, hinges, or the chain and sprockets are telling you something is loose, dry, or out of alignment.
- The gate will not latch or stay closed. A gate that will not latch is a security problem and a liability problem. It also invites wind damage, because an unlatched gate swings freely and slams in Texas storms.
If any of these signs are familiar, call (254) 330-8718. A quick look is free, and a small repair now prevents a big one later.
Our Gate Parts & Welding Process - Step by Step
- 1
We look and we listen. Every job starts with a full inspection of the gate, the posts, the hinges, the rollers, and the opener if you have one. We watch the gate go through a full cycle and listen for the specific sound it makes. That tells us more than a photo ever could.
- 2
We tell you what we found, in plain English. Before any work starts, you get a clear explanation of what is wrong, what it will take to fix it, and what it will cost. No line items you do not understand, no vague hand-waving. The price is settled before a single bolt is turned.
- 3
We do the work right. Hinges get welded, not just bolted. Posts get set in proper footings. Rails get cut out and replaced, never just patched over. Every weld is ground smooth and every part is matched to the weight and use of the gate.
- 4
We test it like we are going to live with it. After the repair or rebuild, we run the gate through full open and close cycles, check the alignment, test the latch, and watch for any binding or noise. If you have an opener, we verify it is not straining against the gate.
- 5
We stand behind it in writing. Every job is covered by our 90-Day Done Right Promise. If it is not right, we come back and make it right. No paperwork, no arguing, no exceptions. That is the Keystone Standard, and it applies to every gate we touch.
How Much Does Gate Parts & Welding Cost in Keller?
Gate parts and welding prices in Keller depend on the weight of the gate, the condition of the existing steel, and how much fabrication the repair requires. A simple hinge replacement on a standard driveway gate typically runs $180 to $340. A rail repair with custom welding usually lands between $250 and $600 depending on how much steel needs to be cut out and replaced. A full post replacement with new concrete footing is generally $400 to $900, because it involves digging, setting, and rehanging the gate. Roller replacement on a sliding gate is usually $150 to $350, and latch or lock repair runs $100 to $280.
What affects the price most is the weight and size of the gate. A 16-foot ornamental iron estate gate costs more to work on than a 10-foot tube steel gate, because it requires more material, more time, and heavier equipment. Rust damage also matters; the more metal we have to replace, the higher the material cost. To avoid overpaying, get a written estimate before work begins, ask what parts are being used and why, and skip any contractor who will not itemize the job. Every estimate from Ironworks Gate Co. is free, detailed, and fixed before we start. Call (254) 330-8718 and you will know exactly what you are paying for.
Gate Parts & Welding Near Keller - Our Service Area
Ironworks Gate Co. serves Keller and the surrounding communities, including Watauga, North Richland Hills, Trophy Club, Colleyville, Hurst, and as far out as Newark, Rhome, New Fairview, and Pecan Acres. Most gate parts and welding calls in Keller proper are reached the same day. If you are in a neighboring city, plan on a response within one business day. We also provide Gate Parts & Welding in Aurora and Gate Parts & Welding in Haslet. Wherever you are in the Keller area, the same crew, the same warranty, and the same standard apply.
Serving Keller, TX - Our Local Coverage Area
We’re based in the Keller area and know this community well, and we also provide Gate Parts & Welding in Haslet. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Keller
Gate parts and welding covers the structural and hardware repairs that keep a driveway gate hanging correctly, moving smoothly, and latching securely. It includes hinge replacement, post replacement, rail repair, custom fabrication, roller replacement, and latch or lock work. At Ironworks Gate Co., it means the full metalwork scope, from a small bracket to a complete gate rebuild.
Most hinge, roller, and latch repairs are completed in a single visit, usually within one to two hours. Larger jobs like post replacement or extensive rail welding may take half a day to a full day, depending on how much concrete work and fabrication is involved. We will give you a clear time window when we schedule, and we will be there when we say. Call (254) 330-8718 to get a specific timeline for your gate.
Most gate parts and welding repairs in Keller fall between $150 and $900, depending on the component and the amount of welding required. Hinge replacements are typically $180 to $340, rail repairs $250 to $600, and post replacements $400 to $900. A free estimate gives you the exact number before any work begins. Call (254) 330-8718 for a quote.
Yes, we service FAAC operators, and we frequently repair the gates and hardware they are mounted to across Keller. FAAC systems are well built, but they rely on a gate that is square, balanced, and running on good hinges and rollers. We handle both the operator and the steel underneath it, so the whole system works together.
In most cases, yes. Ironworks Gate Co. answers the phone 24 hours a day, 7 days a week, and we keep Emergency Gate Parts & Welding in Keller, TX with same-day availability for Keller homeowners with a gate that will not close or cannot be secured. If your gate is stuck open, stuck shut, or hanging off its hinges, call (254) 330-8718 and we will get someone out.
Every gate parts and welding job we complete is covered by our 90-Day Done Right Promise, in writing. If something is not right within 90 days, we come back and make it right. No paperwork, no arguing, no exceptions. That promise applies to the parts we install and the welds we lay.
You do not need to do much. Clear a path to the gate so the technician can bring tools and welding equipment to the work area, and if you have pets, keep them inside during the visit. We handle the rest. The technician will show up in uniform, explain the work, and give you a fixed price before starting.
Schedule Your Gate Parts & Welding Service in Keller Today
Your gate tells you when something is wrong. If it is sagging, scraping, grinding, or refusing to latch, do not wait for it to fail completely. Call (254) 330-8718 today and speak with a real person. We will schedule a visit, give you a free estimate, and fix your gate the right way, with the 90-Day Done Right Promise in writing. Ironworks Gate Co. has served Keller homeowners for over 42 years, and home is where our work stands.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Keller since 1984.