Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Rhome
Gate parts and welding in Rhome usually come down to one of three jobs: a hinge that cracked at the weld, a post that heaved out of plumb in the clay, or an operator that was never sized for a long ranch driveway. We handle all three, and most Rhome jobs are finished in a single visit. If your gate sags, drags, or has stopped opening entirely, call us at (254) 330-8718 and we’ll get a crew to your property fast, with the truck stocked for the job.
Rhome sits at the rural edge of Wise County where a standard driveway can run three hundred feet or more. The gates out here are different from the ornamental iron you see in Fort Worth subdivisions. They’re pipe-framed ranch gates on 2 to 10 acre lots, often doing double duty keeping both vehicles in and livestock contained. That means the welding and parts work has to be heavier, and it has to account for soil that moves under the posts every season.
Why Ironworks Gate Co. Is Rhome’s Preferred Gate Parts & Welding Company
We’ve been doing this work for over 42 years, and our Gate Parts & Welding team has spent enough time on Rhome properties to know what this soil does to a gate. The black clay in Wise County swells after spring rains and shrinks hard in summer heat. Hinge posts move. Gate geometry shifts. Welds that held fine in March crack by August. A repair that ignores the soil lasts about a season. We don’t do that kind of repair.
Every Rhome job is backed by our 90-Day Done Right Promise, in writing. If the gate isn’t right, we come back and make it right. No paperwork, no arguing. Victor Salinas, our owner, built the company on that standard, and the 400th job gets the same care as the first. A live person answers our phone 24 hours a day, so when your gate fails at 6 a.m. before work, you reach a person, not a voicemail tree.
Our Gate Parts & Welding Services in Rhome
We focus on four areas where Rhome gates fail most: hinge replacement, post replacement, rail repair, and custom welding. Each job starts with a straight answer about what’s wrong and what it costs, settled before we turn a single bolt.
Hinge Replacement
Factory hinge welds on Rhome ranch gates crack because the post moves under the load. We cut out the old hinge, grind the post clean, and weld on barrel hinges rated for the gate’s full weight. On properties along County Road 4380 and the gravel drives off Highway 114, we’ve seen hinge welds crack in under five years when they were never sized for a 16-foot pipe gate in the first place. We size them correctly the second time.
Post Replacement
A gate post in Wise County black clay needs to be set deep and reinforced. If your post is heaving or leaning, we dig out the old footing, set the new post 36 inches deep with rebar, and pour against undisturbed soil. This is the fix that actually stops the seasonal cycle. Near the newer acreage developments off County Road 4377, post heave is the single most common reason a swing gate stops latching.
Rail Repair
Ranch gates take abuse that subdivision gates never see. A cracked top rail or a bowed middle rail weakens the whole frame and forces the operator to work harder. We cut out the damaged section, sleeve and weld in fresh steel, and reinforce the corners so the gate hangs square again. Done right, the repair is stronger than the original weld.
Custom Welding
Sometimes the gate needs to be modified rather than just repaired. We build and weld custom hinge plates, reinforcement gussets, latch brackets, and receiver hitches onto existing gates. If you’re adding an operator to a manual gate, we’ll weld the mounting plate and arm bracket in the exact position the automation spec calls for. That matters more than most people realize.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Rhome
Most Rhome properties have one of a handful of operator brands, and we’re trained and equipped on nine of the major ones, including LiftMaster, DoorKing, and Elite. When a builder-grade LiftMaster on a long Rhome driveway strips its rack and pinion gear, we replace it with parts sized for the gate’s actual weight and travel distance, not whatever the subdivision spec called for. Our trucks carry common parts for these brands so many Rhome repairs are completed the same visit. For Mighty Mule solar setups out on the rural acreages, we stock controllers, arms, and battery trays.
Common Gate Parts & Welding Problems We See in Rhome Homes
- Builder-grade operators failing early. Developers specced operators for short suburban drives, but Rhome gates are heavier and travel farther. After five to eight years of pushing a long ranch gate through clay-heaved geometry, the gear strips or the motor burns out. The fix is an operator rated for the actual load, not a like-for-like swap.
- Manual gates retrofitted with automation but no loop detector. Homeowners add an opener to a gate that was never wired for one. Now they want a vehicle loop so the gate opens automatically from the inside. That means trenching across a gravel driveway that buckles with freeze-thaw cycles. We handle the conduit, the loop, and the controller wiring in one job.
- Slide gate V-track rollers binding after storms. Hail and high winds dent the panels, but the hidden damage is down in the track. Muddy caliche packs around the V-track rollers, they seize, and the motor overloads trying to slide the gate. We clear the track, replace seized rollers, and re-set the rail so the gate rolls clean.
- Solar battery death in late summer. Rhome has a lot of solar-powered operators on long driveways where running power to the road wasn’t practical. But our summer heat cooks sealed lead-acid batteries in two to three years. We see a surge of dead-battery calls every late August. We replace them with deep-cycle batteries rated for Texas heat and test the panel output while we’re there.
Pricing for Gate Parts & Welding in Rhome, TX
Here are honest ranges for what gate parts and welding work runs in Rhome, based on the jobs we’ve done across the area:
- Hinge replacement: $180 to $420 per hinge, depending on gate weight and whether we’re reinforcing the post at the same time.
- Post replacement: $350 to $850 per post, including digging out the old footing, setting new steel or wood posts 36 inches deep, and concrete with rebar.
- Rail repair or custom weld reinforcement: $150 to $600, depending on how much steel we’re cutting out and replacing.
- Full custom hinge and latch rebuild on a ranch gate: $500 to $1,200 for a typical 14 to 16 foot pipe gate.
What moves the price is the gate’s weight, the condition of the posts, and whether the operator has to come off and be remounted to get the geometry right. Before any work starts, you get a written price you approve. No open-ended hourly billing, no surprise invoice at the end. We also honor a $50 discount on any repair over $250, a free second opinion on any written estimate, and a permanent 5% discount for seniors and veterans.
We Also Serve Cities Near Rhome
Our crews serving Rhome also cover neighboring communities across the Wise-Tarrant county line. We run regular routes to Newark, Haslet, Keller, and North Richland Hills. If you’re just outside Rhome proper on the county roads near Newark or in the Haslet growth corridor, we can usually reach you within the same window as an in-town call.
Serving Rhome, TX - Our Local Coverage Area
We’re based in the Rhome area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Rhome
Because the post is moving. Wise County’s expansive black clay swells after spring rain and shrinks in summer drought, and that cycle pushes gate posts out of plumb by fractions of an inch season after season. The hinge weld becomes the stress point. The fix is setting the post deeper with rebar and concrete, and welding on hinges sized for the gate’s actual weight. Call (254) 330-8718 and we’ll tell you if the post needs re-setting or just the hinge replaced.
Yes. We weld the operator mounting plate and arm bracket onto your existing gate frame, set the post bracket, and install a solar panel, battery tray, and controller sized for your gate’s weight and daily cycles. We’ll also discuss adding a vehicle loop detector, which means trenching across your drive. On long Rhome gravel drives, that trench needs to be deep enough to survive freeze-thaw cycles without buckling. We do the whole job, including the conduit and wiring.
That depends on what failed. If it’s a stripped rack and pinion gear from years of pushing a heavy ranch gate, replacing the gear might buy you a year or two. But if the motor burned out, you’re better off putting that money toward an operator rated for your gate’s actual weight and travel distance, not a like-for-like swap. We’ll give you both prices before you decide. Estimates are free, and the repair price always includes the 90-Day Done Right Promise.
UL 325 is the federal safety standard requiring automatic gates to have entrapment protection, usually photo eyes or contact edges, so the gate reverses if something is in its path. Yes, you need it. We include proper entrapment protection on every operator installation and repair. On ranch gates with livestock and kids on the property, we’ll often recommend both photo eyes and a reversing edge, and we’ll show you how to test them.
Usually both. The heavy spring rains in Rhome wash mud and caliche into the V-track, the rollers bind up, and the gate climbs out of the rail. We clear the packed mud, replace any seized or worn rollers, and re-set the rail so the gate tracks true again. We’ll also check the operator’s force setting, because a gate that’s been binding has likely been overloading the motor. Call (254) 330-8718 for an exact quote, free.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Rhome and the surrounding Wise County communities.
If your gate is sagging, cracked at the welds, or not opening this morning, call (254) 330-8718 now. A live person answers, we’ll get a crew to your Rhome property fast, and you’ll know the price before any work begins. Done right, and backed in writing.